Chierda V25 25 Watt High Power Repeater
1. 25 watt high power
2. IP66 Waterproof
3. Allows for 2 repeaters linking
4. Color LCD backlit screen
5. Channel/frequency lock
6. Low temperature mode
7. Portable design and easy installation
Product Overview

The Chierda V25 is a UHF FM repeater built to extend radio coverage across large sites. It delivers up to 25 W output power on UHF 400-470 MHz, carries 16 programmable channels, and uses F3E modulation with 12.5 kHz narrowband and 25 kHz wideband channel spacing.
The chassis measures 190 x 75 x 215 mm. That size keeps the unit compact enough to move between locations, and the layout is straightforward to install. Operating voltage covers DC 12 V to 24 V, so the repeater can run from the dedicated power supply or from the vehicle power supply that ships in the box.
A manual low temperature mode warms the unit before operation in cold conditions. Two V25 repeaters can be linked when one unit does not reach far enough. The enclosure is rated IP66, which covers dust ingress and strong water jets.
Key Features
- 25 W maximum output power on UHF 400-470 MHz, with selectable high and low power settings
- IP66 enclosure for dust and water jet protection at outdoor and industrial sites
- Two-repeater linking to extend coverage beyond a single unit
- 16 programmable channels configured through the included programming cable
- Low temperature mode with automatic heating for operation down to -30°C
- Color LCD backlit screen for channel and status reading in low light
- Channel and frequency lock to hold programmed settings against unauthorised changes
- Compact 190 x 75 x 215 mm body that is simple to carry and install
- DC 12 V to 24 V input for dedicated supply or vehicle power
Functions and Performance
Output Power and Power Selection
The transmitter is rated at 25 W output, and the measured maximum sits at 25 W. Operators can switch between high power at 22-25 W and low power at 5-8 W. High power suits sites where the signal has to cross distance or obstructions. Low power lowers current draw from the supply for shorter working links.
Low Temperature Mode
Cold weather changes how RF hardware behaves, and the V25 handles this with a mode the operator enables by hand. Once activated, the repeater heats itself and continues working within the -30°C to +60°C operating range. In warmer conditions the mode can be switched off to save energy rather than run the heater unnecessarily.
Linking Two Repeaters
Two V25 units can be linked to extend the covered area. A single repeater fills one zone, and the linked pair carries coverage further than either unit manages alone. This suits long sites and open ground where one installation point cannot see the whole area.
IP66 Enclosure
The IP66 rating has two parts. The first digit stands for dust protection at level 6, which means no dust ingress. The second stands for water protection at level 6, which means protection against strong water jets. The housing is built for outdoor and workshop conditions where dust and spray are present.
Channels, Display and Control
The repeater holds 16 channels, and the color LCD is backlit so channel numbers and operating status stay readable in dim light. A channel and frequency lock keeps programmed settings in place, so the unit cannot be retuned from the front panel by whoever happens to be on site. Channel data is written through the programming cable supplied with the repeater.
Raspberry Pi Connectivity
Chierda states that the V25 can be connected to a Raspberry Pi to strengthen signal performance and open up further functions. Buyers planning this route should confirm the interface and software requirements with our sales team before ordering.
What’s in the Box
- Repeater x 1
- Programming cable x 1
- Vehicle power supply x 1
- Dedicated supporting power supply x 1
- User’s manual x 1
Applications
- Farms and agricultural operations that need coverage over open ground and outbuildings
- Base sites where one fixed repeater has to serve handheld and mobile radios across the site
- Large areas where two linked V25 units reach further than a single installation
- Cold climate installations where the low temperature mode keeps the repeater running through winter




Technical Specifications
General
- Frequency Range: UHF 400-470 MHz
- Channel Capacity: 16 CH
- Channel Spacing: ±12.5 kHz (Narrowband) / ±25 kHz (Broadband)
- Operating Voltage: DC 12 V ~ 24 V
- Operating Temperature: -30°C ~ +60°C
- Frequency Stability: ±0.5 ppm
- Antenna Impedance: 50Ω
- Dimensions: 190 x 75 x 215 mm
- Ingress Protection: IP66
Transmitter
- Output Power: 25 W
- High Power Mode: 22-25 W
- Low Power Mode: 5-8 W
- Intermediate Frequency: 160 MHz / 465 MHz
- Modulation Method: F3E
- Spurious Emission: -60 dB or less
- Maximum Frequency Deviation: Wide ±5 kHz, Narrow ±2.5 kHz
- FM Noise: Wide ≤45 dB, Narrow ≤40 dB
Receiver
- Intermediate Frequency: 150 MHz / 455 MHz
- Sensitivity: 0.2 μV (Wide) / 0.25 μV (Narrow)
- Squelch Sensitivity: 0.15 μV (Wide) / 0.2 μV (Narrow)
- Adjacent Channel Selectivity: ≥70 dB (Wide) / ≥65 dB (Narrow)
- Intermodulation / Spurious Rejection / Image Rejection: ≥55 dB
- FM Hum and Noise: ≤-45 dB (Wide) / ≤-40 dB (Narrow)
- Working Bandwidth: ≤±7 kHz / ≤±5 kHz
- Modulation Type: F3E
- Audio Distortion: ≤5%

Company Profile
Founded in 1988, CHIERDA specializes in the R&D andmanufacturing of professional wireless communicationproducts, including two-way radios, mobile radios, andrepeaters. As a National High-Tech Enterprise, we arecommitted to “Quality First” and “Driven by Innovation.”
With ISO 9001 certification and SEDEX compliance, CHIERDA products meet CE, FCC, IC, RoHS, and other international requirements. Today, we serve customers in over 100 countries and regions, providing reliable wireless communication solutions for diverse markets and industries.
1988
ON-TIME DELIVERY
MANUFACTURING BASE
EMPLOYEES
TESTING INSTRUMENTS
GLOBAL MARKETS
FAQs
Do you support OEM/ODM services?
Yes! We are a manufacturer offering OEM and ODM services. We can design and customize products according to your specific requirements.
What is your MOQ?
For sample testing, we recommend starting with an order of 2 pieces. Please contact us for more information about bulk order requirements.
Can you offer free samples for testing?
Generally, customers need to pay the sample fee in advance. However, once your order reaches the required quantity, we will refund the sample fee.
Can I place a sample order to test product quality?
Absolutely! You are welcome to place a sample order to evaluate our product quality before making a bulk purchase.
Can I get a better price for large orders?
Yes! We offer more competitive pricing for bulk orders. Generally, the larger your order quantity, the better the price.
How long does it take to ship my order after payment?
Our typical order processing and dispatch times are:
Sample orders: 1–3 days
Bulk orders: 5–8 days
Custom production: 15–30 days
When can I track my shipment online?
We usually provide the tracking number within 2 days. Once you receive it, you can check your shipment status and updates online.
What payment methods do you accept?
We generally accept bank transfers, Western Union, MoneyGram, Trade Assurance, and other payment methods. If you prefer a different payment option, please contact us. We will do our best to accommodate your needs.
How do you ensure product quality?
We use an MES production management system to track the manufacturing process of every product. All products undergo 5 inspections before shipment, and our First Pass Yield (FPY) exceeds 99.4%.
What is your warranty policy?
Radios: 12-month warranty
Accessories: 6-month warranty
We also provide remote technical support. Please contact us if you have any questions or need assistance.
















